Monday, November 24th, 2008
As I mentioned earlier in the season, we had a St. Croix Prescott EXL pellet stove installed in the basement.
Before the Winter season really began, I had my doubts on whether or not the pellet stove would heat the entire house. I was worried that it’s location would hinder the airflow to all the rooms upstairs. Well, I am happy to inform you that the stove does heat the entire house. I mean, if we keep the master bedroom door shut, it does. The master bedroom is over the garage and the furthest room from the stove. It’s also the coldest room, which is why we keep the door shut. When the time hits 10:30PM, the new digital thermostat cranks the heat in that room up to 65 degrees. That’s good enough for me.
We have had some nights already where the temperature has been in the 20s. I think that’s Winter and enough to tell me that the heating situation is going to be okay. I did try burning a fire in the regular fireplace a few times while running the pellet stove. The fireplace actually made things worse. It sucked so much air out of the house, all the rooms dropped a few degrees. Fireplaces are remarkably inefficient and really shouldn’t be used, in my humble opinion. If you want to run something in your fireplace, run a free standing wood stove or a wood stove insert. Even burning a fireplace for aesthetics on a cold day will freeze out the rest of your house. Nuff said.
Okay, we are having a little issue with the pellet stove.
A few nights ago, I tried to start it up. The start up procedure really isn’t very difficult on the Prescott. It basically consists of pushing the “on” button. Once the “on” button is pushed, the room blower turns on for about 10 seconds and the auger turns until the burn pot is approximately half way full of pellets. As the auger is turning, the ignitor kicks on and the pellets light up. It’s fun to watch and I sit there almost every time I light the stove doing just that. I smile when I see that flame dancing around inside that pellet stove.
Back to a few nights ago…when I tried to light the stove this particular time, I pushed the button. The fan turned on for about 10 seconds and then the stove just shut off. I am not sure if the auger ever turned to drop pellets into the burn pot.
I tried to light the stove a few more times when I noticed the #2 light blinking on the control board. I thought this was a little strange, since I had never seen that light blink before. I pulled out the owner’s manual and looked up that error code. Apparently, a lack of negative pressure causes the stove not to light and the #2 light to blink.
What can cause a lack of negative pressure? Well, a really windy day can do it, an open pellet stove door, a fireplace burning upstairs perhaps, a clogged air feed pipe or a clogged exhaust vent pipe. I am sure there are others, but these are the ones I remember.
Since I had a fire already going upstairs in the fireplace, I chalked the whole thing up to that. I got the pellet stove going in this instance by pulling the rubber tube off the vacuum switch and lightly sucking on it. When I heard a little “click,” I pushed the on button again. From here, things were fine. I held the crimped hose for a few minutes and then I hooked it back up the proper way.
Well, I tried to light the stove again the next night. The same thing happened. Since we had no fire going in the fireplace, I thought perhaps there was a clogged area in the stove somewhere that is causing the lack of vacuum, or negative pressure.
Let’s make a really long and boring story a bit shorter and to the point.
I cleaned out the entire stove about 10 times and nothing has changed. Every night, I suck on that hose to get the stove up and running. I have been reading the owner’s manual as well as some websites that deal with this kind of situation, but nothing has helped. One website said that a clogged exhaust vent is the sure-fire problem. I got excited and took off the clean-out cap. A little pile of ashed dropped out, but nothing changed.
This afternoon, I called the pellet stove dealer. I told them that I had pretty much narrowed the problem down to a faulty pellet stove vacuum switch and that I would need the tech to come out and take a look. Before we swap out the switch, I want him to hook up a vacuum gauge to see if there is proper negative pressure. If there is, we can replace the switch…if not, we have to do a bit more digging.
I keep going downstairs to investigate this issue. It is in my blood that I try to diagnose this problem myself. The only things I don’t have are a vacuum gauge or a new vacuum switch. I guess I need those things to solve the problem.
If you have ever experienced something like this with your pellet stove, please let me know. I am racing against time here. I want to beat the repair guy and figure this out myself.
Related posts
Thursday, November 6th, 2008
Now, I know this isn’t nearly as exciting as politics, but it’s important nonetheless.
I got a trailer hitch.
I went over to Home Depot the other day with another $100 gift card that I earned from my debit/credit card points. I wanted to pick up some stakes for the new baby pine trees that are due to arrive soon as well as some programmable thermostats.
On the way over, I said to myself, “Hey man, why don’t I pick up that trailer hitch I have been thinking about too?” Then, after I agreed to myself in the affirmative, I though, “Jay, you are wicked fine.” See folks, this is why I use this as my personal blog.
I did my thing and picked up the other products that I might write about later on. I then walked over to the hardware isle, where they keep the trailer hitches. I saw some pretty cool stuff over there. I found the hitch that I wanted and then took one look at the pin that goes through the assembly. The pin wasn’t bad, it was just that cheap little clip that held the pin in that made me pause from concern.
Reese Towpower Trailer Hitch
I decided that the cheap little clip wasn’t doing it for me, so I picked up one of the locking ones instead. At least this way I know it’s not going to fall out while pulling my cargo. You can see what I am talking about in the photo above. The keys are hanging out of the pin.
Reese Towpower Trailer Hitch on BMW X5
I am putting this photo up for my brother to see. He warned me that I didn’t get enough of a drop. I told him that the drop was sufficient because the hitch itself wasn’t that high. There is a two inch drop on this hitch. Basically, I just wanted to point out the height of the hitch from the ground.
Related posts
Tuesday, August 26th, 2008
Well, the guys came over yesterday to install the new St. Croix Prescott EXL pellet stove. As you might recall, our previous pellet stove was a Harman P38. I was a little nervous about switching brands because I had gotten used to Harman. Also, Harman has very good reviews. The reason I couldn’t get a Harman this time is because they are all backed up and we may not have even gotten one this season.
It took the installers about 3 hours to finish the installation. When everything was in, they fired it up to make sure everything was working properly. One of the installers noticed one issue…the auger wasn’t turning, so no pellets were falling into the burn pot. the auger motor was working fine, just not the auger itself. We made an appointment for the service guy to come out today. By the way, I could have fixed this. It was easy. I actually was almost done fixing it when the doorbell rang. That’s me beating my chest.
Today, the repair guy came out and fixed the auger issue. The small set screw on the auger shaft wasn’t tightened properly, so it wasn’t catching on the auger motor.
I must say, this unit is very nice. It has auto-light, which was very important. I am going to hook up a thermostat, so the pellet stove can shut down and start up on its own. Also, the auger and fan is much quieter than the Harman. The whole system just seems to be more elegant. For a few hundred bucks more, I am happy that I went with this model.
Here are some photos…
St. Croix Prescott EXL pellet stove
St. Croix Prescott EXL pellet stove control panel
St. Croix Prescott EXL pellet stove inside venting
St. Croix Prescott EXL pellet stove outside venting
What’s nice is that the outside venting is under the porch. The necessary clearances are 24″ away from the porch and 12″ off the ground. Also, since we used the fresh air kit, the clearances from windows and doors is only 9″. I would say that’s one of the huge benefits of pellet stoves.
Related posts
Saturday, July 26th, 2008
I know it’s only July, but believe it or not, that’s about two months too late when someone is trying to get a pellet stove installed.
I stopped by the local pellet stove store the other day to pick out my new Harman P68 Pellet Stove. This is top of the line and has everything I want in a stove. There is a thermostat and auto light and everything else I can think of. You can understand my excitement about this after I received a “price lock-in” at $4.85 a gallon from our heating oil company. As it turns out, a lot of other people are excited about Harman stoves as well.
I walked into the store and told the sales guy that I wanted a…He said, “If you are going to say Harman, you aren’t going to see it for a while.” He explained that all the Harman stove models are way back ordered and I wouldn’t see it until way into the season. While this annoyed me, it also gave me a chance to look at some other stoves.
I looked around and picked out a St. Croix Prescott EXL. This has the thermostat option as well as auto-light. When it gets too hot, the fire goes out. When it gets too cold, the stove automatically fires up again and cooks until the whole thing happens again. I am telling you, these things have come a long way.
I put a deposit down on that stove and they are going to come do a site visit, just to make sure the whole thing is going to work out, permit-wise. I think it will.
I also looked at some wood stove inserts for the fireplace upstairs. They look really good. I told the guy that I really wasn’t all too attracted to bringing wood inside again, since my childhood was filled with that. Then, he showed me the bio-brick. A bio-brick is a two pound brick made out of compressed saw dust. Basically, it is a big wood pellet. You can order them by the ton, just like pellets. I though this was wicked cool and now plan on getting a regular wood stove insert for the fireplace next season.
I will let you know what happens with the site visit.
Related posts
