Justa Rollin’ Right Along


Installing a Pella Sliding Glass Door

Friday, June 13th, 2008

As I am sure I have mentioned numerous times, we needed to replace the downstairs in the . There was some rot at the bottom of the . Just this morning, I realized why. Remember that big long post (directly below) about ? Well, it now all makes sense.

When it rains, the back overflows. The water falls, hits the ground and splashes. Guess where the water hits. That’s right, the bottom of the . Good thing I am working on the project. These new are vinyl and the exposed is inside the house, so that should help things.

I had Lowe’s do the install. Actually, it was a contractor that works with Lowe’s. I was a little nervous about the whole thing because I really didn’t know how good a Lowe’s contractor could really be. I have zero experience with them. It ends up that this guy did a better job than I ever expected.

This is the old door. I removed the door knob and all the other goodies I put on it, like the automatic closer. These were . I don’t really like because they are a bit more difficult to deal with. There were no on these and I kept thinking they were going to open by themselves. I really like the we had installed.

This is the rot at the bottom of the door. This and the fact that one of the outer of glass was broken prompted the replacement.

These are some photos of the installation. A nice guy who immigrated from Poland about 20 years ago did it. We talked about Communism and Socialism and all that stuff. It was pretty fun. We talked about the ups and downs of different types of government. He said he really loves this county and there is no other like it anywhere. See, I even found a little first hand education in the process.

When you make an appointment to have a Lowe’s contractor come out to measure the job, they also take note of any extra work that needs to be done. Since this door is a few inches shy of the previous door, there was some work that needed to be done. When Lowe’s calls you the next day to give you the price on the job, they give the price for the materials, the standard installation and any extra work. In this case, the extra work cost over $500. That was more than the installation price.

When he was here, he kept telling me that he was going to make it look nice. After I got the price, I was wondering what in the world could be costing an extra $500. After he finished up, it appears that he did all the trim on the inside. He did all the caulking and waterproofing too. This stuff, plus the reframing of everything was the cause of the extra money. He even got rid of all the junk. I was pretty impressed.

Overall, the installation was a bit pricey (probably double of what it should’ve been), but it is a complete job. All I need to do it paint up the trim on the inside. I would definitely use the service Lowe’s offers again and probably ask for this installer.

Bookmark and Share

Related posts

How To Fix a Loose Sliding Glass Door Handle

Friday, November 9th, 2007

This just goes to show that I will actually post anything on this blog when I have the time. Now, to the fun stuff.

Ok, since we have moved into this house, we have had this loose handle on the that goes out to the . I always said that I was going to replace it, but never got around to it. It’s been over two years now and I suppose enough is enough. I can be lazy sometimes, but c’mon. How can I expect my beauty queen to use a door with a loose handle on it? I just wasn’t raised like that.

Since I had today off, I thought it would be nice to take a leisurely stroll down to Lowes in Middletown. I had to get some deer screening, posts (which I got) and the door handle for the . I picked up the other stuff and wandered over to the handle aisle. I looked at the selection and noticed that they didn’t have what I wanted. From looking online, I knew these were kind of expensive at $47.50 and $29.50. I always thought they were cheaper than that for some reason. I wasn’t too upset. Also, all I needed was the outside part. I grabbed something else instead…some nice stainless steel nuts and bolts.

I compared the threads with the bolts in the other door handle packages.

Before I go any further, let’s get down to the reason the handle was loose in the first place. The two screws that hold the thing together were kind of rusted in place. There was no way to loosen or tighted these two bolts. Over the years, I guess the handle loosened up and couldn’t be tightened. (Yeah, I should’ve cleaned that)

How did I get the handle off then? I drilled the two bolt heads off. Above is a picture of the door with no handle.

When I say rusted, I mean rusted. I thought that since I had that long bolt to work with, I could just grab them with my channel locks and twist. Well, I did that and here is what happened.

Hmmmm…what the heck was I supposed to do now? I had broken both bolts. They were really weak, by the way. I thought about drilling then out, by I couldn’t do that without totally messing up the handle. Instead, I got out my handy new Dremel and started cutting.

I knew the bolts couldn’t be rusted all the way inside the handle. After I grinded the handle all the way down to the bolt, I twisted them right out.

What a wonderful achievement, if I don’t say so myself. Before I did this, I came very close to running down to the hardware store for a new handle.

Here is a photo of the handle back in place…this time, nice and tight. The new bolts were threaded perfectly. I had to use those washers because the bolts were a hint too long. Also, I cleaned and oiled the track, which allowed the door to slide much smoother and easier. Now, there won’t be so much stress on the handle when we open the door.

Mad peace to you.

Bookmark and Share

Related posts





Free Online Ads
Motorcycle Classifieds
Boats For Sale
Free Auto Ads
Free Pet Classifieds