Tuesday, August 26th, 2008
Well, the guys came over yesterday to install the new St. Croix Prescott EXL pellet stove. As you might recall, our previous pellet stove was a Harman P38. I was a little nervous about switching brands because I had gotten used to Harman. Also, Harman has very good reviews. The reason I couldn’t get a Harman this time is because they are all backed up and we may not have even gotten one this season.
It took the installers about 3 hours to finish the installation. When everything was in, they fired it up to make sure everything was working properly. One of the installers noticed one issue…the auger wasn’t turning, so no pellets were falling into the burn pot. the auger motor was working fine, just not the auger itself. We made an appointment for the service guy to come out today. By the way, I could have fixed this. It was easy. I actually was almost done fixing it when the doorbell rang. That’s me beating my chest.
Today, the repair guy came out and fixed the auger issue. The small set screw on the auger shaft wasn’t tightened properly, so it wasn’t catching on the auger motor.
I must say, this unit is very nice. It has auto-light, which was very important. I am going to hook up a thermostat, so the pellet stove can shut down and start up on its own. Also, the auger and fan is much quieter than the Harman. The whole system just seems to be more elegant. For a few hundred bucks more, I am happy that I went with this model.
Here are some photos…
What’s nice is that the outside venting is under the porch. The necessary clearances are 24″ away from the porch and 12″ off the ground. Also, since we used the fresh air kit, the clearances from windows and doors is only 9″. I would say that’s one of the huge benefits of pellet stoves.
Related posts
Saturday, September 9th, 2006
Last year, in the middle of winter and after the second delivery of heating oil, I made a vow to myself. I said that I would get either a wood burning stove or a pellet stove. I said that I would get it over the summer as to avoid the rush. Well, August rolled around and I happen to remember my vow. I really tried to avoid it because I just didn’t want to drop a few grand for a stove, but I kept thinking about how it would feel in the middle of January as I enjoy the warm flame.
I had recently cut up about a cord of wood, so I was really trying to find a good woodstove. I found one at a local dealer and was about a day away from getting it delivered when I found out that I would need more chimney pipe than anticipated. I didn’t want the look of all that chimney pipe sticking out of my roof in the front of the house and there was no other suitable place to put the stove in the interior, due to all the clearances required by the local building code. I decided to purchase a Harman P38 Pellet Stove instead. The clearances are much tighter and the exhaust vent is much, much smaller, as I will show in a few photos below. Here is a great post Paul wrote on woodstoves vs. pellet stoves.
I had the stove delivered along with a ton of pellets so I wouldn’t have to worry about that for a while. I picked up a piece of Bluestone from a dealer up in Mt. Tremper, NY. The piece is 36″x36″, which would cover the clearance I needed. It also saved about $200. I cut a 6″ hole in the wall behind the stove for the exhaust pipe and installed the wall thimble. I attached the Duravent pipe to the wall thimble and ran the pipe through to the outside. One note: I could have installed this stove much closer to the corner (2″), but since both walls of the corner were outside walls, I was forced to have a 12″ pipe clearance from the inside corner and an 11″ clearance from the outside corner. After the pipe was installed, I put the stainless steel turbo vent cap on the outside end of the pipe (photo below).
After everything was installed properly I started up the first fire. What an amazing machine! The stove gets to a certain temperature and the fans kick in to blow warm air out into the room. Also, the exhaust is barely visible and not all that hot. I had the building inspector come over a few days later to give it a passing grade.
The stove manufacturer calls for an outside air vent if you have a smaller and especially well insulated home. We can actually feel the suction when we close the doors in the house, and being only 1150 square feet, I felt that an outside air vent would be a good idea. This takes the air from outside, burns it and sends it out the exhaust pipe, without using any air from inside the house. The kit for this is about $100. $100 I didn’t want to spend, plus, I enjoy making things myself.
I decided that a piece of automotive exhaust flex pipe with a 2 3/4 inside diameter pipe would fit perfectly on the intake adapter.
I cut a hole in the sheetrock so the pipe would just fit through. I then cut a similar hole outside through the vinyl siding and plywood.
Then, I secured the flex pipe to the intake adapter using a sheet metal screw.
After that was set, I went outside the cut off the excess pipe and to attach the custom cover I purchased (dryer vent cover). From the photos below, you can see the exhaust vent (top) as well as the intake vent (bottom). All I have to do now is caulk the sides of the intake vent on the outside and paint and caulk the pipe on the inside and I will be ready for nice cold winter air to be pulled into the stove for clean, efficient burning.
One last note, you can see that I planted a few Arborvitae and a nice little Lilac bush in front and on the side of the vents. In a few years, they will grow large enough to cover the corner of the house and the vent covers.
Related posts
