Wednesday, April 1st, 2009
Okay, I have been waiting for this post for some time now. It is a follow up to my previous post, “Cleaning Gutters & Installing Amerimax Gutter Covers.” If you visit that post, you can see some comments going back and forth concerning these gutter covers and other gutter covers in general.
I had these gutter covers installed in June of 2008. When I had them put on, the installer really didn’t want to do it. He said that he hated these things and was always taking them off of people’s gutters. I believed him because when I looked in the back of his truck, there were piles of old wire leaf guards. Also, he is a gutter cleaner, so if everyone got gutter covers, he would be out of business.
There are some issues that drive people away from gutter covers. I would say the two main issues are ice buildup and pine needles getting stuck in the covers. Some of the comments in my other post describe six foot icicles. I will tell you about my experience with these gutter covers and then I’ll talk about icicles.
Do you want the verdict? Okay, here it is….SUCCESS.
We went through the summer, autumn and winter and all that we have to show for it is one oak tree leaf stuck in the gutter cover. That’s right, one leaf stuck in the whole gutter system. During the winter, we had a few six inch icicles over the front door. That’s it. These gutter covers didn’t cause ice buildup in the least and handled the heaviest of rainfall. Also, leaves slid off with ease. We have many oak trees around the house and I watched the leaves come down on many occasions. We don’t have any nearby pine trees, so I can’t comment on the pine needle issue.
Let’s talk about icicles. Please read this short article on what causes ice dams and icicles found here.
As I said above, I had some comments describing huge icicles that were allegedly caused by gutters or gutter covers. The truth of the matter is, if a house is properly insulated, you won’t have an ice problem. Ice dams and icicles are caused by warm air leaking through the ceiling of your home and warming the roof. When that happens, the snow melts and water runs down the roof to hit a cold gutter or gutter cover. The water freezes and causes an ice problem. Ice dams and icicles are a symptom of the problem, not the problem itself. The real problem, is heat loss.
Since the house we live in is properly insulated, we didn’t have any ice problems. I will tell you that we live in Connecticut and had about five or six nice snow falls. A few of them were about 12″ in depth. This is valuable information when trying to compare locations with ice issues.
So there you have it. My conclusion is…if your house is properly insulated, go for it and get some gutter covers. It will save you money on gutter cleanings and will make life easier. If you have an insulation problem, get the problem fixed before you install gutters or gutter covers. If not, you may find yourself outside one snowy night tearing them off your house in a frenzy.
Related posts
Tuesday, August 26th, 2008
Well, the guys came over yesterday to install the new St. Croix Prescott EXL pellet stove. As you might recall, our previous pellet stove was a Harman P38. I was a little nervous about switching brands because I had gotten used to Harman. Also, Harman has very good reviews. The reason I couldn’t get a Harman this time is because they are all backed up and we may not have even gotten one this season.
It took the installers about 3 hours to finish the installation. When everything was in, they fired it up to make sure everything was working properly. One of the installers noticed one issue…the auger wasn’t turning, so no pellets were falling into the burn pot. the auger motor was working fine, just not the auger itself. We made an appointment for the service guy to come out today. By the way, I could have fixed this. It was easy. I actually was almost done fixing it when the doorbell rang. That’s me beating my chest.
Today, the repair guy came out and fixed the auger issue. The small set screw on the auger shaft wasn’t tightened properly, so it wasn’t catching on the auger motor.
I must say, this unit is very nice. It has auto-light, which was very important. I am going to hook up a thermostat, so the pellet stove can shut down and start up on its own. Also, the auger and fan is much quieter than the Harman. The whole system just seems to be more elegant. For a few hundred bucks more, I am happy that I went with this model.
Here are some photos…
St. Croix Prescott EXL pellet stove inside venting
St. Croix Prescott EXL pellet stove outside venting
What’s nice is that the outside venting is under the porch. The necessary clearances are 24″ away from the porch and 12″ off the ground. Also, since we used the fresh air kit, the clearances from windows and doors is only 9″. I would say that’s one of the huge benefits of pellet stoves.
Related posts
Saturday, August 23rd, 2008
Last Saturday, the pellet stove installer came out for a site visit. He checked out the location of the installation and took a few pictures for the file. It’s good to have a site visit, just to make sure everything will be OK for the installation.
He gave me some papers to bring down to the town office for the permit application. Things are a little different here in CT than in NY. Here, you have to fill out the permit information and then, the project needs to be approved by the inspector. This took a few days, because I am sure this fellow is out inspecting all these new pellet stoves people are putting in. In NY, I think I remember just handing the guy the paperwork and him looking at it and giving me the green light. Back in the old town, you could pretty much put up a housing project on your front lawn and get it approved.
Oh yeah, permits here go by the cost of the project. The more expensive the project, the more you are going to pay for a permit. It might be that way in NY…I don’t remember.
By Thursday, the permit was approved by the inspector. I gave the pellet stove company a call to set up an install date. We settled on this Monday coming up, which isn’t bad. I just want this thing in so I can stop thinking about it. I also ordered four tons of pellets. Boy, those pictures are going to be fun.
This blog post is over. At this point, I have nothing else to add.
Related posts
Wednesday, January 23rd, 2008
The installer arrived this morning at about 8:30. I was very pleased to greet him in the driveway holding the plans in my hand. I felt like a puppy looking out the window.
It is extremely nice to see this thing being put together. There are already some things that I would’ve had trouble with, but he seems to be banging away in there like it’s nobody’s business.
Here are a few photos that I snuck. He is installing the base cabinets first, and then I guess the wall cabinets. I just hope he gets the majority of it done today with just the trim to complete for tomorrow.
These two photos below were taken at about noon. The majority of base cabinets are installed and he is now working on the wall cabinets.
Ok, these next photos below were taken at about 3PM. Most of the base cabinets are installed and the wall cabinets are almost done. There are a few hiccups that he had to fix up, but nothing huge.
I took these photos below at about 5PM, right after the skilled installer left. Man, he measured a lot of stuff and did a better job than I would’ve. Anyway, here they are…
The counter top for that small base cabinet directly above is too long. I think they forgot about that one being more shallow than the rest. I guess we have to get a new one of them. Tomorrow, he is coming back to do the crown moulding, the kick plates and all the spacer wood. Then, we will put the counter top on and cut the hole for the sink. After that, he is done and I will do the plumbing for the sink and purchase and install the dishwasher.
Related posts
